The Eterra EX-30 Micro Brush Mower for mini excavators is ideal for clearing brush from roadsides, ditches, driveways, and much more.
Designed for Mini Excavators, the EX-30 Micro Excavator Flail Mower packs a lot of punch into a small and lightweight package. In fact, the EX-30 Micro is the lightest mower in the 30" class. At 320 lbs., the Micro can be operated on the smallest excavators, but still provide awesome performance. But wait a minute? Does less weight imply that this product is weak? NOT A CHANCE. This mower has never once been returned to SkidSteerSolutions.com and there has never been any reported housing failures. This product is made in the USA and built for easy maintenance and long lasting results. The EX-30M is designed for mini excavators weighing in at 2200 lbs. to 7000 lbs. with flow rates from 8-26 GPM. If this mower sounds like it will fit your machine and your needs, be sure to watch the videos, chat with us or give us a call for more information. Keep reading for more details on the construction of this amazing product.
With cutting capacities up to 2", this mower straight up performs With the ease of use and the compactness, you will be able to access the smallest of properties and mow small brush, berry bushes and grass with the most compact of excavators. The EXM-30 Micro is specifically designed to have a low swing weight to allow the smallest excavator to have the maximum reach without becoming unstable. There just is nothing else like it.
Select Product Options Above
All Eterra drive systems have been proven to be strong and reliable. Eterra uses a 2 lb. blade and premium Permco USA motors. The welding and machining is exceptional. Fit and function, OUTSTANDING! Many of these have been sold in the USA, Canada and Australia. Eterra would be happy to supply you with references upon request to Skid Steer Solutions. Eterra customers are the company's best salesmen.
With the compact flail design, you will be able to access the smallest of properties and mow small brush, berry bushes and grass into a fine mulch which leaves you with virtually no clean-up.
The EX-30M is built from lightweight and strong materials. The cutter shaft is electronically balanced for the most efficient operation and longest operating life in it's class. If you are looking for the best in show, then Eterra mowers have it hands down.
Please note that the EX-30M comes with a blank universal mounting plate. The customer is responsible for mounting the specific coupler required for your excavator. Due to the high speed and pressures involved, a case drain line is required to operate this implement. A case drain is a low pressure line that travels from the mower head back to your oil reservoir. It allows pressure to be directed away from the motor seals and back to your oil tank. This increases your seal and motor life substantially. Check with your dealer as some newer machines including Yanmar have a return to tank setting which makes a case drain unnecessary.
The Eterra Cutter Shaft
Eterra uses 5" DOM Tubing for their cutter shafts to insure a strong and long wearing product. Ettera does not use steel pipe. Eterra cuts it themselves and constructs one of the toughest shafts available. Then it is electronically balanced so when the flail is operating, it is hard to tell. No shaking from side to side or up and down. This is just another step that Eterra adds to make their mowers much better than the competition. Eterra's goal is to produce the best possible product and deliver it to you in the most economical manner.
Drawn Over Mandrel (DOM)
Strong and well-finished DOM is an electric resistance welded tube tested for soundness of weld and drawn through a die and over a mandrel. This process imparts significantly improved mechanical properties to the tube, due to the cold working process. It is considered a high quality tube, and is normally constructed from SAE 1020 or 1026 steel. Note that, technically DOM refers to the process by which the tube is finished after having started as an ERW tube. Technically, DOM is not a type of steel tube, but rather a process. As so often happen though - in common use the term has become accepted to mean a specific type of tubing rather than a process. In this case, when people say "DOM" they normally mean an ERW tube drawn over a mandrel at (close to) room temperature and made from SAE 1020 steel. It is normally drawn to O.D. and I.D. dimensions. Here is what the Steel Tube Institute of North America has to say about DOM:
"The manufacturing process for DOM tubing begins with coils of steel, which are slit to the proper width for the desired tube size. The strip is cold formed and passed through an electric resistance welder which joins the edges together, under pressure, to complete the tubular shape. After testing the weld's integrity, the tubing is cut to length for further processing.
The cold-drawing process creates a uniform, precision product with substantially improved tolerances, surface finish and tensile strength, increased hardness and good machinability. In this process, the tube is cleaned and annealed, and one end of each length is squeezed to a point so it can be gripped by the drawing mechanism. The tube is then drawn through one or more dies and over mandrels. This reduces the diameter of the tube and thins its walls to the required dimensions in a controlled fashion to provide the qualities desired in the finished product. Metallurgic-ally, drawing improves the tube's concentric, tensile strength, hardness and machinability. Close dimensional accuracy is achieved through tight control of both outside and inside diameters."
Case drain not required for Bobcat, Yanmar, Kubota, Caterpillar or Case Excavators.
Note: Every excavator is different. Many machines (Especially older models) use only two pumps. One to control your stick and rotation. One for track drive and auxilliary flow (your mower). For machines that have this type of pump arrangement, it is not possible to drive the machine forward and cut at the same time. You will need to drive forward, stop and then sweep back and forth for cutting. For operators with newer machines like Kubota and any Yanmar, you have three pumps so you can drive and cut at the same time.
A Message from the Owner of Eterra
"Why are we less expensive than the other guys? It's simple. All Eterra products are produced in high volumes directly in our facilities in Bellingham, Washington and sold directly on the web. We do not start building these one at a time when you place your order. We also do not use dealers. The other guys add 25 - 40% to allow dealers to sell their mowers. That is not how we do business. We believe the best way to sell our products is directly with to our customers. We sell it, and we support it. This means you save serious money by dealing directly.
Something else to note about our competitors. Many of them make comparisons to our mowers that theirs are heavier. If you know anything about these mowers, that makes no sense. We design for maximum strength for the machine weights specified so that you get an effective mower that won't flip your machine. If we knew nothing about design, we could just add steel and call it a day, but that would short change our customers. Adding steel does not make a good mower. It adds unnecessary weight that can endanger the operator. Others are now using a metal spring disk as a dampener where we use a water jet cut rubber disk. We have 15 years experience with this design and not one failure or replacement due to wear. Our system is proven to last and is lighter and quieter. We are waiting to see how long it will be before they have to change their design as their mowers are just too heavy, use a higher parts count, operate more noisily, and the replacement disks cost $1400 where if you ever needed one ouf ours, they are less than $100. Good design always wins. If you want good design, buy Eterra. If you want weight and un-necessary parts, then buy theirs.
Our competitors are struggling with us in the market so they will say anything to you about our mowers just so they can take the sale, so here is one more thing to add. We offer a no nonsense warranty. 1 year, full replacement with no questions asked. If it fails, we take care of it. We have a full parts selection in stock. No one else will offer you this. They always make you send the unit back for testing which will cost you serious down time when you need the equipment to be working most. We don't operate like that and never will."
Skid Steer Solutions, Inc. offers a 1-Year Limited NO-HASSLE Warranty on all attachment products and their accessories purchased from our website SkidSteerSolutions.com, please visit our warranty page for full details. Our warranty on parts and wear parts is dependent upon the manufacturer's warranty. Please visit our warranty page for more information. To learn about our returns policy, please visit our Shipping and Returns page for the full details.
The carbon steel market is poised to grow by 699.35 MT during 2020-2024 progressing at a CAGR of almost 8% during the forecast period." (Source: Business Wire)
This is what we are seeing all across the industry; day after day new emails from vendor's telling us that their prices are rising, every order we make for materials needs to be revised because the last price is no longer valid, and for good reason. The cost of steel materials has been steadily increasing throughout 2020, and it unfortunately has not slowed into 2021. The reduced capacities of companies in this industry due to Covid-19 health and safety regulations continues to have an impact. As a result, we are forced to increase our list pricing for 2021 and add a steel surcharge to off-set the rising costs that is projected to continue this year. We apologize for any inconvenience this may have on our close and prospective customers. We we will do what we can to keep our prices low when the opportunities are found, but right now we are left with little options.
Thank you for your understanding and continued support.